Film clings to a roll, dust sticks to a molded housing, or a label feeder picks two sheets. Installing an industrial ionizer bar does not solve these problems unless the bar reaches the charged surface at the right point in the process. This guide helps a Thai factory specify, compare, accept and maintain a static neutralizer. The core decision is whether the device improves the actual product at production speed, under the factory’s installation and air conditions.
Confirm that charge is causing the defect
Begin with a process map, not a catalogue. Record which material contacts which surface, where separation occurs, where voltage rises, and where the defect appears. For a web line, measure after unwind, after the nip and before inspection. For molded parts, compare the voltage immediately after ejection and after transfer into a tray. Record film width, part dimensions, line speed, starts and stops, temperature, relative humidity, measurement instrument and measurement distance. A noncontact electrostatic voltmeter is sensitive to geometry and stand-off distance; compare readings taken consistently.
Link those readings to outcomes: dust counts, web misalignment, sticking, double feeds or inspection rejects. Mechanical friction, blown dust, web tension and humidity can produce or worsen the same symptoms. Check grounding of conductors first. Grounding alone may not drain charge from insulating film or resin, so air ionization may be appropriate there. An ionizer does not physically remove dust already attached to a product. It can reduce electrostatic attraction while cleaning and extraction address the particles themselves.
Distinguish physical neutralization from monitoring. Our ESD control and monitoring guide covers records, alarms and audits. An ionizer bar delivers ions to a product or web. A green monitoring status does not demonstrate low product voltage; an operating bar does not satisfy a factory-wide ESD management program by itself.
Choose the installation point before the model
Locate the bar between the last significant charging event and the place where the process fails. A bar after unwind may have little value if a downstream nip charges the web again. Compare possible positions using an actual machine drawing: available distance to the target, width and lateral wander, guards, rollers, grounded metal, cable routing, air lines and access for cleaning. For a curved housing or a deep tray, a bar aimed at one surface may leave the hidden face charged. A second bar, a nozzle or a changed part orientation may be needed.

Do not treat a manufacturer-specific mounting distance as universal. Simco-Ion’s instructions differentiate speed and hybrid bars and account for adjacent grounded metal. Verify the chosen model’s own clearance and installation drawings. Measure the voltage at both the center and edges of the widest product. When comparing quotations, require the same measuring positions. Otherwise, a location advantage can look like a product advantage.
Time under the active ionization zone falls as web speed rises. Dividing effective zone length by line speed is a useful first estimate of exposure, but it does not predict final voltage because airflow, charge and geometry also matter. Test minimum, nominal and maximum production speeds, acceleration, stopping and restart. Some Simco-Ion bars use entered web speed and mounting distance for automatic tuning; incorrect settings can compromise that function. An acceptance test performed only at reduced speed is insufficient.
Decide between bars, nozzles and blowers
Bars suit continuously moving film, sheet and flat products where the active length can cover the width. A nozzle or gun may reach a recess or small isolated part more effectively. A blower can serve a larger work area. The key question is whether positive and negative ions reach the target surface without disrupting the process.
An air-assisted model can extend ion transport, but compressed air has a running cost and can move lightweight workpieces or stir up dust. State air pressure, flow, quality, piping distance and operating hours in the RFP. Ask the supplier to demonstrate the lowest air condition that meets the process requirement and, where feasible, an air-free option. Do not assume that greater air flow always produces better quality.
AC, DC and pulsed-DC methods exist, with model-dependent controls and operating ranges. No one method is universally best. For electronics ESD control, offset voltage, commonly called ion balance, matters alongside decay time. For film cling, product surface voltage and the actual sticking outcome may be more decisive. Keep equipment qualification metrics separate from product-quality criteria.
Read catalogue decay time with its test conditions
IEC 61340-4-7:2025 describes methods for assessing ionizers through offset voltage and charge-decay time under specified conditions. It encourages users to adapt conditions for application qualification and periodic verification. Therefore, compare quoted seconds and volts only after identifying the charged-plate instrument, start and end voltage, distance, air setting, test point and target geometry. Different test conditions do not make a fair ranking.
SMC’s IZT series technical data explicitly says that its charged-plate results are selection guidance because performance varies with target material and size. KEYENCE also publishes product-specific performance, not a universal bar specification. Put three columns in a comparison sheet: manufacturer’s rated conditions, the proposed installed conditions and the factory’s acceptance conditions.
Define acceptance values from the process. Examples include a product surface voltage below an agreed threshold at the defect point, fewer double feeds per batch, or fewer dust-related rejects at fixed inspection settings. The threshold must come from the product’s risk and quality standard; there is no universal voltage number in this article. State measurement repeatability and the rule for inconclusive results. Use the same lots, speed and environment for ON/OFF comparisons where possible. Rare defects need longer production follow-up; a short FAT cannot prove a long-term defect-rate reduction.
An 11-point RFP for an industrial ionizer
| Item | Factory input | Supplier response |
|---|---|---|
| Workpiece | Material, dimensions, finishes, variants | Applicable range and exclusions |
| Quality problem | Dust, cling, double feed, false inspection | Cause hypothesis and proposed method |
| Baseline | Voltage, point, distance, speed, humidity, instrument | Site measurement plan |
| Motion | Maximum speed, acceleration, stops, wander | Worst-case test method |
| Installation | Drawings, grounded metal, guards, service access | Bar length, stand-off and mounting drawing |
| Air | Availability, pressure, flow, quality and cost | Required flow and air-free alternative |
| Controls | PLC inputs, alarms, run permission | Signal map and fault behavior |
| Utilities | Power, protective earth, cable route | Electrical and grounding requirements |
| Safety and environment | Solvents, combustible dust, washdown, temperature | Applicability and extra engineering needed |
| Acceptance | FAT/SAT voltage, speed, quality and locations | Test fixture, instruments and report |
| Maintenance | Cleaning windows, owner, spare strategy | Cleaning and replacement procedures |
Mark unknown values as “not yet measured” and make the site survey the first priced activity. Supply real parts, rejected samples, process video and machine drawings. Normalize quotations to include brackets, power supply, air piping, cabling, PLC changes, safety work, installation, tests and operator training. Purchase price alone misses compressed-air consumption, cleaning downtime, electrode replacement and local support.
FAT: demonstrate repeatable equipment behavior
Factory acceptance testing should use agreed good and bad samples, smallest and largest sizes, surface-finish variants and representative material lots. Record measuring locations, bar distance, speed, air, humidity and power. If the test stand cannot reproduce the production rollers, tension or airflow, state those differences and carry the affected decisions into SAT. Test both charge polarities when both occur.
The ANSI/ESD STM3.1-2024 method gives charged-plate test configurations. A standard instrument test asks whether the ionizer meets a defined performance method; product voltage measurements ask whether the process problem is solved. Specify which one governs each contractual acceptance item. Test alarms, loss of power, air loss and communication loss where the model supports them. Check what the PLC and HMI show and how suspect products are handled. An ionizer’s self-diagnostic alarm is not automatically a machine safety function.

SAT: qualify the installed process at full speed
Site acceptance must cover production speed and the actual machine, not just a clean bench. Include the most charge-prone material, extreme part sizes, restart after a stop, splices and changeovers. Record temperature and humidity and define when seasonal follow-up is needed. Measure immediately before and after the bar, at the point where recharge can occur, and where quality is decided. Good voltage directly below a bar can coexist with bad voltage at the downstream nip.
If the device is installed ahead of vision inspection, hold camera lighting, focus, exposure and field of view constant. The industrial camera selection guide explains how those variables affect image results. Changing the vision recipe during an ionizer comparison would hide the source of improvement. Record unit serial number, electrode condition, operator, lot, speed, air, measuring instrument calibration, before/after voltage and defect count. When the result fails, first check position and settings, then revisit the charging or dust source before replacing the model.
Carry the acceptance method into maintenance
Contamination on emitter points, worn electrodes, altered airflow and piping faults can reduce performance. KEYENCE recommends scheduled inspection and cleaning with power off; Simco-Ion documentation also relates contamination to reduced neutralization. The maintenance interval depends on model, dust load, material and operating hours. Establish it from measured degradation, not an arbitrary universal calendar.
Keep a commissioning baseline at fixed measurement points. Separate a quick routine check from a fuller periodic verification, with the instrument ID, positioning jig, standard speed, reference part and pass limit written down. Compare voltage and defects before and after cleaning. After electrode or bar replacement, repeat the same performance measurement instead of treating power-on as proof of recovery. Follow the maker’s high-voltage isolation and cleaning instructions. Check availability of spare emitters, controllers and cables in Thailand against the cost of a stopped line.

Three application decisions
Film after unwind. Map the unwind, nip and inspection points. Measure both sides if practical, including edge positions at maximum web width and wander. Compare a bar close to the charging source with one just before the defect point. If a downstream nip recharges the film, consider a second stage. FAT can compare devices with film samples; SAT must use actual rollers, tension and speed. Assess extraction alongside neutralization when airborne dust is present. If the solution works at slow speed only, test exposure time, friction, entered speed and electrode condition separately.
The RFQ should specify maximum web speed, width range, expected wander, feasible stand-off, and the position of grounded rollers. A bar can nominally span the web and still leave charged edges. Test the edges during FAT where the stand permits, but reserve a production-speed edge and downstream-defect check for SAT. If voltage falls without a reduction in dust rejects, inspect dust generation and extraction instead of immediately increasing ionizer output. Preserve a charging map so a future material change can be diagnosed quickly.
Molded parts in trays. Deep trays and recesses may block ions from a bar. Evaluate actual part orientation, a nozzle, a rotating presentation or a tray change. Excessive air may shift a light part and upset robotic picking. Separate pick failure, dust contamination and scratches as outcomes. Group SKUs by charge behavior, shape and mass, then test worst cases. Define a sample approval step before adding future SKUs to the same setup.
Measure immediately after mold ejection, after transfer, and after the part lands in the tray. This identifies whether demolding or tray contact dominates charging. If charge reappears during the drop, review tray material and drop height rather than simply moving the bar upstream. Include the lightest part, a thin part prone to warp, and material or color variants whose additives may change behavior. A demonstration using only the largest part cannot qualify every SKU.
Electronics assembly. Ionization complements grounding, work surfaces, packaging, handling and documented ESD controls. It does not replace them. Specify charged-plate locations and polarity-specific decay and offset tests where required. Also test whether ions reach the component inside the real fixture, behind shelves and at both the loaded and lifted operator positions. A controller’s “normal” status is evidence of its self-check, not a measurement of charge on the component.
Measure with the fixture populated and at the operator’s real hand positions. Ask quality to approve the ESD limits and test locations, production engineering to verify that the bar does not block reach or sight, and maintenance to own cleaning and periodic verification. Route status signals into monitoring if required, but do not substitute them for measurements at the component. Repeat the test when a fixture or work posture changes.
Assign responsibility from purchase to operation
Quality owns the defect definition and acceptance limit; production engineering owns installation feasibility; maintenance owns utilities and service access; operations supplies real running conditions; procurement aligns scope and lead time. The supplier proposes the model, installs and tests it, and transfers procedures. Name each owner explicitly. Retrofitting may require guard changes, mounting design, PLC wiring and planned downtime. Decide who pays for adjustment and retest if SAT fails after a successful FAT.
The handover package should contain the selection rationale, installation, wiring and air drawings, model and serial numbers, settings, FAT/SAT reports, instrument calibration, cleaning and replacement instructions, spare parts and training record. Daily checks and alarm response must be understandable to the Thai operators who will perform them. Test that understanding during training instead of assuming that an English manual is enough.
Before ordering, confirm local availability and lead time for replacement emitters, power units and cables. If a single failed bar would stop the line, a local spare may be justified. If a redundant installation can maintain quality, stocking may be different, but any decision to continue running after a fault belongs to production and quality. Define the alarm response, the treatment of work in process and the lot range to trace. The supplier should disclose service scope in Thailand and the maximum practical downtime for replacement.
Avoid misleading numerical comparisons
Decay time only compares fairly when starting and ending voltage, distance, air and charged-plate positions are equivalent. SMC’s 1000 V to 100 V examples cannot be ranked against a different maker’s number obtained under different conditions. Ion balance at the center of a bar may differ at the web edge or downstream. A very tight catalogue figure copied into a factory specification can become an unrepeatable acceptance test if the instrument cannot resolve it.
For ROI, estimate the fraction of defects actually caused by static, the recoverable fraction, scrap cost, rework, line stops, air use and maintenance labor separately. Do not assume that all dust defects vanish. Present a range before the trial, then update it with production data. IEC 61340-4-7:2025 evaluates ionizers; it does not cover use with flammables, explosive items or EMI evaluation. A device’s qualification also does not certify a whole ESD program. Keep product quality, equipment performance and machine safety approvals distinct.
A practical decision sequence
In the first week, collect defect images, lot, time, humidity and speed; map voltage at consistent points. If charge does not correlate with the failure, investigate dust generation or mechanical sticking before buying an ionizer. If charge is implicated, survey at least two feasible positions and compare width, distance, grounded metal, maintenance access and controls. Demonstrate candidates with the same samples and conditions. Set the pass limit, instrument, repeat count and retest rule before placing the order. Complete SAT at production speed and carry the same measurement points into periodic verification.
Filter quotations by mandatory constraints before scoring features or price. A long-range bar offers no value if the installation can be safely close; a cheap short-range bar is unusable if a wandering web violates clearance. At FAT confirm sample performance and signals; at SAT confirm the line effect. Write down who moves brackets, who pays for extra wiring and when retesting happens. For maintenance, preserve center and edge, slow and fast, before and after cleaning baselines. Those records help separate seasonal humidity changes from electrode degradation.
Make each approval explicit. Quality signs the defect criterion, production engineering the mounting and machine interfaces, maintenance the access and isolation method, and operations the representative speed and SKU mix. A supplier demonstration is useful but may not represent production. List each unresolved condition before contracting, assign it to FAT or SAT, and state what happens if it cannot be demonstrated. Separate the quick routine check from a deeper periodic verification. After cleaning, a value that does not return to baseline should trigger a structured check of emitters, power, airflow, mounting and material changes before declaring the ionizer unusable.
FAQ
What determines the price of an ionizer bar?
Active length, required distance and speed, balance control, air assist, diagnostics, communications and environmental ratings all matter. Compare a complete installed and tested scope, including utilities and service, against the process pass criterion.
For a fast web, is mounting the bar closer enough?
Sometimes it helps, but it is not a universal rule. Check the model’s minimum safe distance, nearby grounded metal, web wander, width and air settings. Run SAT at full speed and measure at the downstream quality point.
Which matters more, ion balance or decay time?
The product risk decides. Electronics ESD applications may prioritize offset voltage; film cling may prioritize product voltage and sticking at production speed. Define both measurements and their limits separately. Do not re-label a standard charged-plate result as a product-quality guarantee.
Will ionization eliminate dust defects?
It can reduce attraction caused by charge, but will not remove the particle source or dust already deposited. Investigate extraction, cleaning, airflow, friction and storage. Track product voltage and defect rate separately.
Can a standard bar be installed near solvents or combustible dust?
Do not assume so. The plant safety team and supplier must check hazardous-area classification, substances, ventilation and equipment suitability. IEC 61340-4-7:2025 does not assess use with flammable or explosive items.
Conclusion
Successful industrial ionizer selection connects the charging event, available exposure time, distance to the workpiece and downstream recharge. Catalogue decay time is a starting point, not proof at production speed. Survey the line, align the RFP, qualify device behavior at FAT, verify process benefit at SAT, and preserve the measurement method for maintenance.
If your Thai factory is comparing ionizer bars or deciding where one can be retrofitted, contact TOMAS TECH with the workpiece, line speed and observed defect. We can help structure the site survey and acceptance criteria while the solution is still being defined.