Blog

2026.11.09

Three-Phase Phase Loss and Sequence Relay Selection for Thai Factories

Three-Phase Phase Loss and Sequence Relay Selection for Thai Factories

When selecting a three-phase phase loss and phase sequence monitoring relay, simply marking “phase loss detection” or “reverse phase detection” in a model selection table does not fulfill equipment protection requirements. You must define, as a single specification, the measurement location, voltage and frequency, detection of phase loss during operation, regenerative voltage from the motor, output contact usage, restart conditions after reset, and testing methods. This article is a practical guide for owners, panel builders, and maintenance engineers involved in new or retrofit control panels in Thai factories, so that all parties share the same criteria from RFQ through FAT/SAT. Connection and live testing of devices must be performed by qualified electrical engineers in accordance with local requirements and equipment risk assessments.

First, Decide: “What Event Should Stop What?”

Phase loss refers to the loss of one phase out of three; reverse phase means the phase sequence differs from the intended order. The impact varies by equipment—motors, pumps, conveyors, fans, compressors—and you cannot use the same circuit for loads where only notification is needed and those where continued operation is unacceptable. The RFP should specify the protected load, abnormality type, detection point, stop target, fault indication, and reset conditions. If you merely write “install phase loss relay,” the panel builder may assume monitoring the incoming power, while the user expects detection of phase loss during motor operation, leaving a gap in understanding.

A monitoring relay typically observes three-phase voltage and switches contacts accordingly. These contacts are connected to control circuits, contactor coils, PLC inputs, etc. Do not treat the monitoring relay itself as the main circuit breaker. Which contactor or breaker trip circuit operates, and which load is de-energized, must be separately designed and verified. Short-circuit/overcurrent, ground fault, overload, and machine safety functions are not to be replaced by a single monitoring relay. When a power abnormality is detected, the equipment’s response must be completed by dividing roles between protection devices and control logic.

Do Not Confuse Phase Loss Monitoring with Phase Sequence Monitoring

Phase sequence monitoring is mainly for detecting wiring swaps at commissioning or changes on the power side after relocation. Phase loss monitoring detects the disappearance of one phase, but the detection conditions during operation differ by model and circuit. Voltage-type relays are affected by “regenerative voltage,” where voltage appears on the lost phase while the motor continues to rotate by inertia or on the remaining two phases. ABB’s CM-PFS documentation states that if the regenerative voltage is less than 60% of nominal, phase loss during two-phase operation can be detected. This threshold applies to that specific model and is not universal.

Omron K8DS-PH’s product literature clearly states it supports phase sequence and phase loss at startup, as well as phase loss during operation. Its catalog also notes that phase loss may not be detected under light-load conditions because of regenerated voltage; verify the actual load conditions. In contrast, Schneider Electric’s RM17TG series documentation indicates monitoring of phase sequence and complete loss of one or more phases. This shows that the scope of “phase loss” functionality cannot be treated as identical across products. For procurement, line up datasheets for candidate models to compare monitoring targets, detection levels, response times, reset methods, and wiring requirements, and decide on a policy for simulating actual load abnormalities.

Three-Phase Phase Loss and Sequence Relay Selection for Thai Factories - figure 1

Correlate Phase Sequence and Rotation Direction On Site

Changing the three-phase sequence can reverse the rotation of directly coupled induction motors. Pumps and fans may appear to operate even in reverse, but this can manifest as reduced flow or cooling performance. However, with inverter drives, mechanical anti-reverse mechanisms, or certain gear configurations, you cannot simply infer final movement from input phase sequence. The RFP’s “correct phase” should not just state L1-L2-L3, but must be correlated with the actual required rotation direction of the equipment. Swapping two phases must be performed by authorized personnel following safe procedures, and acceptance criteria should include not only relay indication but also load operation.

Fix Three-Phase Power Conditions First

The first column in the selection table is voltage. Specify line-to-line voltage, phase voltage, allowable fluctuation, frequency, three-wire or four-wire, neutral usage, transformer and grounding information. Even within “400 V class,” whether the device measures line-to-line or phase voltage, and whether measurement input doubles as power supply, affects wiring and applicability. Even for devices distributed in Thai factories, always confirm the actual incoming system, design voltage, and branch voltage in the panel for each project. Do not select based only on the edge of the nameplate voltage range; check the operating range including normal fluctuations, startup, and power switching.

Omron K8DS-PH’s manufacturer specs are three-phase three-wire 200–480 VAC, 50/60 Hz. Phoenix Contact EMD-SL-PH-400 is a three-phase monitor powered from the measurement voltage, for nominal 400 V three-phase systems; 342–457 VAC is its adjustable voltage-threshold range, and 48–63 Hz is the input-frequency range. ABB CM-PFS documentation specifies three-phase 200–500 VAC. These are examples only; compatibility with one model does not guarantee suitability for another. Especially confirm three-wire/four-wire, neutral usage, and where the monitoring power is sourced in the panel, using both schematics and physical inspection.

Should Monitoring Be Upstream or Near the Load?

Monitoring upstream of the main breaker allows observation of the factory’s incoming three-phase condition, but may not detect phase loss caused by downstream fuses, contactors, terminals, or cables. Conversely, monitoring near the load makes it easier to catch local faults, but in circuits where the measurement power disappears with each stop or switchover, indication and reset become complex. Which is correct depends on the protection target and fault hypothesis. Mark the measurement point with a red circle on the single-line diagram, and clearly state whether the design detects “abnormalities upstream of this point” or “downstream of this point.” Also include three-phase input fuses and relay terminal wiring as part of the measurement path for inspection.

Do Not Casually Monitor Inverter Output Side

Inverter output does not have the same conditions as commercial power sine waves. Siemens’ monitoring relay manual explains that when monitoring downstream of a frequency converter, a waveform without extra zero crossings is required, and a sine wave filter may be necessary. Do not assume that a device labeled “50/60 Hz” can be applied to PWM outputs. Separate consideration is needed for input-side power monitoring, inverter self-diagnostics, and monitoring of motor current or temperature. If placing a device on the output side, confirm with the manufacturer the permissible waveform, frequency, voltage, and connection method.

Do Not Select by “Phase Loss Supported” Alone

Three-phase monitoring relay functions include phase sequence, phase loss, unbalance, overvoltage, undervoltage, frequency, and neutral disconnection. However, not all products measure all items, and even the same terms may differ in algorithm or setting range. Schneider Electric’s catalog distinguishes RM17TG series as monitoring phase sequence and complete phase loss, and other multifunction models as monitoring unbalance, undervoltage, overvoltage, etc. The aforementioned Phoenix Contact model supports phase sequence, phase loss, and unbalance, with the unbalance value fixed at about 30% per product specs. If you select based on “multifunction” without defining the required fault, you may not be able to set the necessary sensitivity or delay.

Selection ItemWhat to Write in RFPEvidence to Confirm
Power/MeasurementLine-to-line voltage, frequency, 3-wire/4-wire, monitoring pointDatasheet and single-line diagram
Detection FunctionsPriority of reverse phase, phase loss, phase loss during operation, unbalance, undervoltage, etc.Function table and test procedure
Sensitivity & DelayTime not tolerating false trips, time to stop on sustained abnormalitySetting sheet, manufacturer’s allowable range
Output ContactsContact type, rating, energized in normal, state during power lossCircuit diagram and contact table
ResetAuto/manual, restart permission conditionsSequence diagram and recovery test
InstallationPanel temperature, spacing, terminals, maintenance replacementPanel layout and actual unit
LoggingPLC/HMI alarms, event time, cause distinctionI/O table and screen test

Treat Thresholds and Times as Product-Specific Values

It is risky to copy values like “stop within X seconds on phase loss” or “always operate at 30% unbalance” into the RFP as general rules. Omron K8DS-PH specs state phase sequence operation 0.1 s ±0.05 s, phase loss (sudden drop from 100% to 0%) within 0.1 s, phase loss detection level 80% ±10%. ABB CM-PFS documentation gives different values for startup delay, etc. Not only model differences, but also the way the abnormality is created, measurement point, and actual load regeneration can affect results. The RFP should specify the allowable stop time and conditions for tolerating momentary dips on the equipment side, and require the supplier to show the proposed model’s spec values and setting rationale.

Stopping instantly is not always safest. For equipment where workpieces remain inside, hydraulic pressure must be held, or airflow drop affects process quality, evaluate stop and restart methods as well. Conversely, if you want to prevent pump reversal, design so phase sequence is confirmed correct before startup permission. Simply shortening “detection time” does not cover the time for the control circuit to process the stop command, the contactor to open, and the machine to reach a safe state. If necessary, link to equipment risk assessment and safety-related control requirements.

How You Use Contacts Determines Fault Behavior

Many monitoring relays have outputs that are energized in normal conditions and drop out on abnormality or monitoring power loss, but this depends on model and settings. If you use the relay contact only for PLC alarm input, the main circuit will not open unless the PLC or software executes a stop. If you wire it into the contactor coil enable circuit, you can design for the contactor to drop on abnormality, but in that case, check contact rating, coil inrush, surge suppression, and bypass paths for manual/auto operation. If using both PLC monitoring and hardwired interlock, decide which is the primary stop and what is logged.

When control power is lost first, only one phase of three is lost, or the PLC stops, trace the contact state separately on the circuit diagram. Simply stating “ON in normal” may overlook the problem of contacts automatically returning on power restoration, causing unintended equipment restart. The relay’s auto-reset and the equipment’s restart permission are separate concepts. If the requirement is for the equipment to remain stopped even after the abnormality clears, and only restart after confirmation and reset, implement and test that latch in the control circuit or PLC. For example, Omron relays are auto-reset, so this distinction is important.

Define the Boundary with Safety-Related Control

Phase sequence and phase loss monitoring are often used for equipment protection or process continuity, but in machines where reversal or stop failure could harm people, they may become part of a safety function. In such cases, simply selecting a general-purpose monitoring relay does not constitute a safety function. Determine the hazard, required safe state, behavior on fault, required performance, diagnostics, and verification from equipment risk assessment. Clearly state the boundary between electrical protection and machine safety in the RFP, and decide which OEM is responsible for safety validation. The general selection tables here do not substitute for individual equipment safety design.

Combine with Distribution Components for a Complete Protection System

Main and branch breakers provide short-circuit and overcurrent protection; contactors switch operation; overload relays and motor protection devices address load-side abnormalities. Phase sequence/phase loss monitors provide condition signals to these devices. If you treat components as separate RFQ items, responsibility for stopping on a given abnormality may be left unclear. Ensure both the single-line and control circuit diagrams allow tracing “when the monitor contact opens, what happens to which main circuit.” Related articles on MCCB selection for Thai factories and magnetic contactor selection are useful for confirming rating and control boundaries.

Three-Phase Phase Loss and Sequence Relay Selection for Thai Factories - figure 2

Panel installation location also affects operation. Placing the device next to high-temperature equipment, on a vibrating door, or deep inside where inspection is difficult may make it hard to meet manufacturer specs for ambient temperature and spacing. Use wiring identification to avoid confusing voltage measurement inputs and control outputs, ensure terminal tightening, ferrules, LED visibility, and model confirmation at replacement, and reflect these in drawings and inspection sheets. Manufacturer’s temperature and spacing requirements differ by product, so review the exact model’s documentation in the BOM. For substitutes, check not only width but also function, detection conditions, contact rating, reset method, and test results.

Summarize Selection Criteria for the RFP on One Sheet

For RFQs, attach the following input table instead of vague terms like “with phase loss protection” to enable comparison. List equipment number and load type, single-line diagram revision, monitoring point, nominal and allowable range for three-phase power, frequent power switching, assumed faults, detection during startup/operation, momentary dip conditions to avoid false trips, stop target, reset and restart, notification recipient, panel environment, spares, and test location. Do not leave items blank; mark as “pending site measurement” or “awaiting OEM response” with responsible person and due date. Price alone does not allow comparison of downtime or maintenance burden, so require a conformity table to the requirements as part of the deliverables.

Suppliers should provide model number, manufacturer documentation version and URL, terminal diagram, setting values, wiring diagram for measurement point, circuits receiving contacts, operation sequence, alarm list, FAT/SAT test procedures, substitute conditions, and local stock or lead time. If a specified abnormality cannot be detected, do not just write “compliant,” but propose the missing fault mode and compensatory measures. For example, if voltage-type monitoring alone is affected by regenerative voltage during operation, evaluate adding current-type monitoring, motor protection, or inverter diagnostics. Even then, do not assume an alternative method is always suitable; judge by actual load and test results.

Example Specification Wording

“Monitor the three-phase input to motor M-101 at the point shown on drawing E-12. Detect reverse phase before energizing, and permit startup only with correct phase sequence. For phase loss during operation, specify with manufacturer documentation the conditions and limitations under which the proposed model can detect, and verify by simulating faults during FAT. On abnormality, disable contactor K-101 and log the abnormality type to the PLC. Do not allow automatic restart on power restoration alone. Define test methods, pass/fail values, and safety measures in an approved procedure.” The identifiers in this example are for explanation; in real projects, replace with the actual load, drawing number, design voltage, stop time, installation environment, and risk assessment.

By pairing each “action” with “evidence” in this way, you reduce disputes after delivery over “it wasn’t in the specification.” Also clarify whether the panel builder’s scope ends at relay wiring or includes OEM software changes. For retrofits, coordinate outage windows, temporary power, existing terminal condition, drawing discrepancies, and timing of stop tests. In Thai factories, aligning the language and approvers for test records among Japanese HQ, local maintenance, OEM, and panel builder reduces rework at installation.

FAT: Trace from Contacts to Equipment Operation

FAT (Factory Acceptance Test) is not just to confirm receipt of components, but to verify state transitions on the panel or equipment per specification. First, cross-check model, settings, wiring, terminal numbers, and drawing revision. Then, apply normal three-phase power and record relay indication, output contacts, PLC input, HMI display, and contactor enable. Simulate reverse phase, phase loss on each phase, and control power loss using safe test devices and procedures, and confirm startup is blocked or stopped as intended. If phase loss during operation is required, do not settle for no-load simulation only; agree on reasonable load conditions with the manufacturer and equipment side.

Injecting faults during FAT does not mean carelessly disconnecting live terminals on site. The fault simulation method must be planned by engineers according to panel and equipment configuration, with isolation, grounding, protection, witnesses, and pre/post restoration checks defined. For reverse phase tests, it is not necessary to actually rotate the machine in the dangerous direction; you can confirm startup blocking with safe simulated signals and check rotation direction separately under permitted conditions. If protection was bypassed for testing, record restoration evidence on the test sheet.

FAT TestObservation PointsItems to Confirm Before Pass/Fail
Normal phase sequence, all phases presentRelay indication, contacts, PLC input, startup enableDesign voltage and correct phase sequence
Reverse phase at energizationStartup block, alarm, contact stateTest power source and safe simulation method
L1/L2/L3 phase lossDetection and stop for each phaseMeasurement point, load condition, model detection limits
Momentary dips/temporary fluctuationFalse trip or required stopEquipment’s allowable time and setting rationale
Monitoring power lossContact dropout and main circuit stateNormal energized state and contact wiring
Power restorationAlarm reset and restart inhibitionManual reset and startup enable logic

Pass/fail values such as “within 0.1 s” are set per project based on the selected model’s datasheet and equipment requirements. Recording whether only the relay indication changed, the PLC received it, or the contactor opened, in time sequence, helps root cause analysis. Since measurement device response and timestamp synchronization have limits, do not set pass/fail values finer than recording accuracy. After testing, restore any temporary wiring changes, setting device positions, parameters, alarm resets, and protective covers, and update the latest circuit diagrams and setting sheets.

Three-Phase Phase Loss and Sequence Relay Selection for Thai Factories - figure 3

SAT: Match Site Power and Actual Load Conditions

SAT (Site Acceptance Test) is the opportunity to confirm that the simulated power used in the factory matches the actual power at the Thai site. Using approved safety procedures, check line-to-line voltage, phase sequence, frequency, terminal labeling, grounding, power switching path, and actual load rotation direction at the receiving point and panel input. Confirm that the panel’s measurement point is connected as planned on site, and that phase sequence has not changed due to separate power cable replacement. Assign load condition tests not possible during FAT to SAT, and clearly state which conditions cannot be safely reproduced on site.

Intentionally causing phase loss on site affects equipment operation and other loads. Do not create faults in the entire factory power system for testing; use approved isolation zones and simulation devices to verify only the required fault modes. If actual load testing is not possible, combine FAT results, manufacturer documentation, continuity checks of protection circuits, and PLC/HMI signal tests, and document unverified risks and future confirmation methods in the handover record. The most important thing for operations is not to mark “all functions passed” if tests were not performed.

Test Operator Actions for Recovery and Restart

Some monitoring relays have contacts that automatically return to normal when phase loss is restored. However, the sequence for operators to confirm the cause, reset contactor or inverter alarms, and safely resume the process must be defined on the equipment side. Clarify whether the HMI “reset” button merely clears the alarm, grants startup permission, or causes the motor to start automatically. Test for unintended restarts on power restoration, PLC reboot, mode switching, and local/remote operation. Include display checks, contact function tests, and phase sequence verification after replacement in periodic maintenance procedures.

Model Management for Purchasing and Maintenance in Thai Factories

Whether approved models can be procured locally affects not only initial quotes but also recovery time during outages. If the exact model is unavailable, do not substitute based only on similar voltage range or DIN rail width. Differences in detection method, regenerative voltage tolerance, contact default state, number of contacts, delay, reset method, terminal layout, environmental conditions, and certifications may require circuit modification or retesting. For approved substitutes, provide a difference table, wiring diagram, setting sheet, and scope of FAT re-execution. When maintenance staff pull parts from stock, ensure BOM, spare parts ledger, and panel nameplate match so equipment and revision are clear.

For fault records, distinguish between abnormalities the relay can differentiate and those the PLC infers, rather than lumping all as “three-phase power abnormality.” Some models cannot distinguish reverse phase and phase loss by LED alone. If the HMI displays a definitive message, verify in testing that it is actually distinguishable. The first-response maintenance ticket should have fields for occurrence time, operating state, relay indication, line-to-line voltage, contactor state, upstream breaker, and replacement history. If the configuration only clears the alarm after power restoration, ensure cause traceability via PLC event logs or maintenance records.

Troubleshooting When “Relay Does Not Operate” During Commissioning

If the relay output does not switch to the enable side even with normal three-phase applied, first check model, terminal arrangement, power range, and LED indication. Using an approved measurement procedure, confirm that all three phases reach the correct terminals and that the line-to-line voltage and frequency at the measurement terminals are within the device’s range. If the phase sequence is opposite to what the device expects, some products will not enable output even with correct voltage. Schneider Electric’s RM17 support documentation also lists incorrect phase sequence as a common cause of output contacts not changing. Before using test equipment, always confirm power isolation, PPE, work permits, and impact on surroundings; do not perform live work based on local custom alone.

If the relay indicates normal but the contactor does not pull in, do not immediately assume relay contact failure. Trace the contact usage side, coil power, emergency stop or door interlock, overload protection, PLC startup permission, and manual/auto switching in order per the circuit diagram. Do not assume NO/NC just by contact number; check with the manufacturer’s contact diagram for both normal and abnormal states. If the contactor pulls in but the PLC still shows abnormal, check for PLC input logic inversion, input power commonality, I/O assignment, alarm holding, and communication delay. Record the state with the fault reproduced, power conditions, time, and contact status, and link cause and countermeasure.

If alarms occur only after starting operation, consider voltage drop at startup, simultaneous starting of other loads, power switching, loose terminals, or actual load unbalance. Decide in advance which points to measure and safe measurement methods, and use the recorder function of test equipment or equipment event logs. Simply loosening thresholds or extending delays may cause you to miss phase loss you actually want to detect. Only change settings after confirming the cause, and compare waveforms, loads, and stop times before and after the change before approval. After changes, re-execute affected abnormality tests from FAT or SAT, and update the setting sheet and as-built drawings with the revision.

If reverse phase is indicated only immediately after relay replacement, check the terminal layout of the replacement device and correspondence with existing wiring. Even if the enclosure width is the same, terminal positions and contact operation may differ between manufacturers. Do not end post-replacement checks with just LED indication; judge by the full sequence of startup block, alarm, contactor opening, and manual reset. Maintenance procedures should specify the drawing revision to read at replacement, spare part model number, required measurement points, and storage location for test records. This way, even if personnel change, you do not have to rely on the vague judgment of “it worked after replacing the part,” but can hand over protection functionality as equipment.

Summary: Linking Product Specs and Equipment Operation

For three-phase phase loss and phase sequence monitoring relay selection, start from the target load and fault mode, then decide power conditions, measurement point, detection during operation, regenerative voltage, contact usage, reset, and installation environment. Then, cross-check candidate model manufacturer specs and limitations, write the required operations to be verified in the RFP, and confirm from contacts to equipment stop, alarm, and restart inhibition in FAT and SAT. Detection times and thresholds are model-specific and must not be treated as universal values. The monitoring relay is only part of the protection system. Only when breakers, contactors, motor protection, control, and operator recovery procedures are linked does the design become usable on site.

If you want to organize three-phase monitoring requirements, candidate model comparison, and FAT/SAT test items for control panel upgrades or new equipment in Thai factories, you can contact TOMAS TECH. We will listen to your actual power and load conditions, stop/recovery operations, and summarize them into specifications that can be shared with panel builders and OEMs.

FAQ

Can a phase loss monitoring relay always prevent motor burnout?

Not always. Results depend on monitoring method, measurement point, fault location, regenerative voltage from the motor, detection time, and stop circuit. Separate protection devices are also needed for motor overload or overheating. Verify detection and stopping under conditions close to actual load.

If I install a phase sequence monitoring relay, is reverse rotation testing unnecessary?

No, it is still necessary. You must correlate the relay’s “correct phase sequence” with the equipment’s required rotation direction on the actual machine. Especially after relocation or cable replacement, check phase sequence indication and actual operation under safe conditions.

Where should reverse phase protection be installed in the three-phase power system?

Decide based on the protection target and power switching boundary. Monitoring only upstream phase sequence may not catch downstream wiring swaps. Indicate monitoring point and stop target on the single-line diagram and confirm on site.

How much detail should be included in the RFP for phase loss protection?

Include not only nominal voltage but also allowable range, frequency, load, measurement point, faults to detect, allowable stop time, and reset/restart conditions. For relay thresholds and response times, require the supplier to attach candidate model documentation and test conditions.

Are FAT and SAT just repetitions of the same tests?

They have different roles. FAT confirms circuit, settings, simulated faults, and state transitions; SAT checks site power, phase sequence, wiring, actual load, and operational recovery. Leave unperformed tests as “unverified,” and decide on alternative evidence and confirmation timing.

References

Product specifications vary by model, revision, and sales region; always check the latest documentation for the selected product at the time of procurement.